Main :: Safety Solutions :: Safety Application Controllers

• Logical AND connection enables partial or full control.

• Uses solid-state output (excluding Expansion Units).

• LED indicators provide details of failure diagnosis.

• TÜV SÜD

• UL

• KOSHA

• Auto Switching and Manual Switching functions support two types of application.

• External indicator outputs enable indicating the switching status of two safety input devices.

• Auxiliary outputs enable monitoring of safety inputs, safety outputs, and errors.

• Detailed LED indications enable easy diagnosis.

• Logical AND connection allows complicated applications in combination with other G9SX-series Units.

• TÜV Product Service

• UL (cUL)

• KOSHA

• The back electromotive force (BEMF) signal is used to determine when the motor has stopped.

• A standard configuration for standstill detection enables immediate application without setup.

• User configuration to adjust settings for individual machines is also possible.

• Detailed indicator displays for fault diagnosis.

• Certified for Safety Category 4 (EN 954-1), PLe (ISO 13849-1), and SIL3 (IEC/EN 62061).

• TÜV Product Service

• UL (cUL)

• Detects the motor speed with a proximity sensor.

• Monitors to see if the motor is below the speed level that has been set for the specific hazard source.

• Enable switch input provided for maintenance work.

• Detailed indicator displays for fault diagnosis.

• Certified for Safety Category 3 (EN 954-1), PLd (ISO 13849-1), and SIL3 (IEC/EN 62061).

• TÜV Product Service

• UL (cUL)

• Detects two wires shorted together with the self-diagnosis function and specifies the location of the problem with the communications function.

• Tell I/O status at a glance from LED indicators.

• Conforms to safety category 4 and SIL 3.

• Controls up to four light curtain sets.

• TÜV SÜD

• UL (cUL)

• KOSHA *2

• Compact design.

• Two-hand Controller model available.

• Simple connection of Expansion Unit.

• High-speed 10-ms response.

• Incorporates LED indicators for monitoring built-in relays.

• Finger protection construction.

• 3-pole, 5-pole and Off-delay Units available.

EN60204-1
EN954-1
UL508
CSA C22.2
No.14

• BG

• UL

• CSA

• Ultra-compact, with models starting at only 17.5 mm wide.

• Can be used with Safety Sensors.

• High-speed 10-ms response.

• Incorporates LED indicators for monitoring built-in relays.

• Finger protection construction.

EN60204-1
EN954-1
UL508
CSA C22.2
No.14

• TÜV Rheinland

• UL

• CSA

• Two-pole, three-pole, five-pole, and OFF-delay models are available.

• Incorporates LED indicators for monitoring built-in relays.

• Finger-protection construction.
 

EN60204-1
EN954-1
UL508
CSA C22.2
No.14

• BIA

• UL

• CSA

• Sensor connectors allow direct connection to F3SN-A, F3SN-B and F3SH-A.

• Reduces wiring and prevents incorrect connection.

• Connection to emergency stop switch also supported.

• TÜV Rheinland

• UL

• PLC I/O Unit-type safety relay.

• Can be used with OMRON PLC models CQM1H and CS1.

• The monitor signal of the safety circuit connects directly to the CPU of the PLC through the internal bus.

• Simplified wiring and space-saving construction.

• TÜV Rheinland

• UL

• Control Unit for F3SN-A, F3SN-B, and F3SH-A.

• Plug in light curtain connectors on both sides.

DEMKO and UL certified in a set with F3SN-A, F3SN-B, and F3SH-A.

• Adds muting function to Safety Sensors.

• Connects to a maximum of 2 Safety Sensors.

• TÜV SÜD

• UL (cUL)